3M™ VHB™ Partition Tape C20F, 8 mm x 16.5 m

3M™ VHB™ C20F is a clear high performance VHB™ Tape. Its cohesive and adhesive properties make it suitable for highly demanding applications where a coloured bond line is undesirable.

This tape shows higher peel (on high energy surfaces), tensile and shear performance than many other VHB tapes due to the increased cohesive strength. The tape thickness of 2,0 mm and the cohesive properties allow the tape to withstand higher tension forces resulting from tolerances between bonded parts.

This product is suitable for the bonding of transparent materials like glass and transparent plastics. Depending on the material and on the environmental influences the pre-treatment of the surfaces with a Primer (e.g. the 3M™ VHB™ Silane Primer for glass) is recommended.

Thickness (mm) AFERA 5006	2,0 mm ± 10 %
Release Liner	Red PE liner
Tape Colour	Clear The tape is clear in colour but not optically clear.
Foam Density	1020 kg/m³
Adhesive Type	High performance acrylic
Adhesive Carrier	Firm, clear acrylic

Peel Adhesion acc. to AFERA 5001, 72 hrs dwell time, Al-film-backing, 2 x 6,8 kg pressure

50 N/cm

Tensile Strength acc. to ASTM D897 on aluminium T-block 24 hrs dwell time, 6,45 cm² bond area, 51 mm/min, RT

1.250 kPa

Static Shear acc. to AFERA 5012; >10,000 minutes to stainless steel; 3,23 cm²

22 °C 70 °C 93 °C 140 °C

1000 g 1000 g 1000 g 500 g

Dynamic Overlap Shear Acc. to ASTM D-1002, after 72h; 12,7 mm/min.; 6,45 cm²; RT

600 kPa

Temperature resistance

Long term 90 °C

Short term 150 °C

Each 3M™ VHB™ C20F application will be reviewed on a project specific basis. Application guidelines will be based upon adhesion test results generated by 3M Technical Service. These project specific application guidelines will be provided to the customer and must be followed during the glass bonding process. Listed below are some typical application guidelines for a 3M™ VHB™ C20F project. However, these do not replace the project specific application guidelines provided by the 3M Technical Service Representative.

• For maximum bond strength, non-glass surfaces should be thoroughly cleaned with a 50/50 IPA/water mixture to remove contaminants. Glass surfaces should also be cleaned with a 50/50 IPA/water mixture followed by treatment of the glass with a mixture of 3M Silane Primer prior to tape application. Some surfaces may require additional surface preparation that will be determined on a project specific basis by a 3M Technical Services Representative.

• Ideal tape application is accomplished when temperature is between 21 °C and 38 °C and the bond is allowed to dwell 72 hours. Initial tape application to surfaces at temperatures below 18 °C is not recommended. However, the use of a primer may lower the minimum application temperature. Contact 3M for more information.

• Bond strength is dependent upon the amount of adhesive- to-surface contact developed. Flat bonding surfaces and firm application pressure develops better adhesive contact and helps improve bond strength. Generally, this means that the tape should experience at least 100 kPa in roll down, vacuum or platen pressure. 3M™ must approve pressure application equipment for 3M™ VHB™ C20F applications.

• After final bonding of the parts, immediate handling strength is achieved and bonded units can be moved as there is no curing mechanism in this process. However, the bond strength will continue to increase as the adhesive flows onto the surface. At room temperature, approximately 50 % of the ultimate strength will be achieved in 10-

20 minutes after pressure application, 90 % after 24 hours and 100 % after 72 hours. The use of a primer may accelerate the bond strength build rate. Contact 3M for more information.

Storage	Store 3M™ VHB™ C20F in original cartons at 21 °C and 50 % relative humidity.
Shelf Life	3M™ VHB™ C20F has a shelf life of 24 months from date of date of manufacture.
Precautionary Information	Refer to product label and Material Safety Data Sheet for health and safety information before using the product. For information please contact your local 3M Office. www.3M.com